Optiview Security Camera TRKPTZ 18NX User Manual

Auto Zooming Tracking  
Dome Cameras  
User Manual  
 
Auto Zooming Tracking Dome Camera User Manual  
Section1 Instruction  
1.1 Production Introducing  
The dome cameras feature high position resolution, high  
speed, low price and selectable communication protocols;  
Widely used in surveillance system.  
1.2 Character  
Built-in English OSD Menu, by which you can change  
dome parameter, set or call preset, and achieve auto tour,  
pattern, auto scan etc.  
The feature will define the activity when the dome  
parks.  
Integrated design making it high reliability.  
Auto panning function with 256 preset positions.  
RS-485 data communication.  
Low noise design.  
With its full 360º horizontal rotation, 180º vertical auto-flip  
to follow object and surveillance of any subject is constant and  
continuous.  
The speed can be adjusted automatically according to  
the zooming times.  
Auto focus, Auto white balance.  
Auto focus lens and auto white balance.  
BLC Function.  
Multi protocols (Pelco-P, Pelco-D, Kalate, etc).  
Baud rate is changeable.  
Alarm input, Alarm output, Alarm action.  
3
 
     
Auto Zooming Tracking Dome Camera User Manual  
The features password protection to prevent  
unauthorized changes to the dome setting.  
A set window can be reversed so that it is the only visible  
tilt area of the scene. ll other parts of the tilt area of the scene will  
be blanked.  
Revolutionary motion tracking technology make it realize  
intelligent surveillance easily with the help of alarming function  
1.3 Function Description  
(1) Setting the dome ID, Baud-rate and Protocol  
Every controlling command has a target camera Address,  
Baud-rate and Protocol, the camera only reacts the controlling  
command in accordance with its own Address, Baud-rate and  
Protocol.  
(2) Object tracking  
The dome can be manually controlled from the control system  
by using the joystick on the controller to move the camera up and  
down, right and left to follow objects under observation.  
In default status AUTO IRIS and AUTO FOCUS control of  
the lens will automatically adjust the picture image on alteration  
of the background illumination to get a best view.  
(3) Proportional Pan  
Proportional pan automatically reduces or increases the pan  
and tilt speeds in proportion to the zooming times. At telephoto  
zoom settings, the pan and tilt speeds will be slower for a given  
amount of joystick deflection then at wide zoom settings. This  
keeps the image from moving too fast on the monitor when there  
4
 
 
Auto Zooming Tracking Dome Camera User Manual  
is a large amount of zoom.  
(4) Auto Flip  
When the dome camera tilts downward and goes just  
beyond the vertical, the dome camera rotates 180 degrees  
automatically. Afterwards, the dome camera starts moving  
upward even you still hold joystick in the down position. Once  
you let go of the joystick after the dome rotates, joystick control  
returns to normal operation. The auto-flip feature is useful for  
following a person who passes directly beneath the dome.  
(5) Setup and call Preset  
Preset function is that dome saves current horizontal angle  
and title angle of pan/tilt, zoom and position parameters into the  
memory. When necessary, dome calls up these parameters and  
adjusts Pan/Tilt/Zoom accordingly so that the camera goes to  
that position again. Operator can save and call up presets easily  
and promptly by using keyboard controller or infrared controller.  
This dome supports up to 256 presets.  
(6) Lens Control  
a. Zoom control  
User can adjust cameras zoom wide or near by using  
controller and get desired image.  
b. Focus control  
System defaults Auto Focus mode, in which the lens and  
camera will automatically adjust the focus to give the best image.  
Focus can also be controlled manually from the  
controller if required.  
Press FOCUS NEAR or FOCUS FAR key to manually  
focus.  
5
 
Auto Zooming Tracking Dome Camera User Manual  
Focus can be manually controlled via keyboard or  
matrix, please refer to control keyboard or matrix operation  
manual for detailed operation.  
When on manual focus status, operations such as  
adjusting positions or preset setting will resume the camera to  
auto focus status.  
The camera will not auto focus in the following status.  
Target is not in the center of image.  
Targets are in near and far at the same time.  
Target is of strong light object. Such as spotlight etc.  
Target is behind the glass with water drop or dust.  
Target moves too fast.  
Target is too big, such as wall.  
Target is too dark or vague.  
c. Iris control  
System defaults AUTO IRIS. Camera can adjust immediately  
according to the alteration of back ground illumination to get a  
steady image.  
Users may adjust Iris manually by using a controller to get  
required image quality.  
Users can call back AUTO IRIS by moving the joystick.  
(7) Auto Back-light Compensation  
Lens has been divided to six areas for back light  
compensation. In a strong light background, camera will auto  
compensate the darker object and adjust light input from the  
lighter area to avoid a mass image that usually presents a sharp  
contrast of brightness and darkness.  
(8) Auto White Balance  
6
 
Auto Zooming Tracking Dome Camera User Manual  
Camera can automatically adjust white balance according to  
the alteration of background lightness to give a true color image.  
(9) Backlight Compensation (BLC)  
If a bright backlight presents, the subjects in the picture may  
appear dark or as a silhouette. Backlight compensation  
enhances objects in the center of the picture. The dome uses the  
center of the picture to adjust the iris. If there is a bright light  
source outside this area, it will change to white. The camera will  
adjust the iris so that the object in the sensitive area is properly  
exposed.  
(10) Day and Night Function  
The IR cut filter of camera module inside the dome can be  
removed by sending special command, so that the camera can  
change from color to mono. The picture is clear even if the  
illumination is as low as 0.01Lux.  
(11) Auto Cruise  
The preset positions are programmed for recalled in  
sequence. This feature is called auto cruise. Up 30 presets can  
be set in each cruise tour.  
(12) Patterns  
A pattern is a saved moving course, the camera will repeat  
its pan, tilt, zoom and preset functions that can be recalled with a  
command from a controller or automatically by a programmed  
function (alarm, park or power-up).  
(13) Auto Scan  
Make the dome scan 360º range in the current position.  
(14) Random Scan  
7
 
Auto Zooming Tracking Dome Camera User Manual  
Make the dome random scan 360º range in the current  
position.  
(15) Frame Scan  
This feature freezes the scene on the monitor when going to  
a preset. This allows for smooth transition from one preset scene  
to another.  
(16) Zones Setting  
A zone is a pan area, defined by a left and right limit, on the  
360-degree pan plane. The spectra dome system is capable of  
eight zones, each with a 6-character label.  
(17) Alarms  
Alarms input:  
The dome has four alarm inputs, which can be programmed  
as high, medium or low priority. When an alarm is received, an  
input signal to the dome triggers the user-defined action (go to  
preset, run pattern, etc.) programmed for the alarm.  
Auxiliary output:  
An auxiliary output is a programmable signal from the dome  
back box that can trigger another device to operate. An auxiliary  
output is programmable to trigger from an alarm or from a  
controller.  
(18) Password protection  
The dome features password protection to prevent  
unauthorized changes to the dome settings. You can open the  
System Information and Display Setup screens, but cannot  
access any of the Dome Settings menus.  
(19) Windows blank  
8
 
Auto Zooming Tracking Dome Camera User Manual  
A set window can be reversed so that it is the only visible tilt  
area of the scene. All other parts of the tilt area of the scene will  
be blanked.  
NOTE: Be the same with only the model of TRKPTZ-18NX,  
TRKPTZ -26NX, TRKPTZ -18NX, TRKPTZ-26NX.  
(20) Auto tracking  
Revolutionary motion tracking technology making it realize  
intelligent surveillance easily with the help of alarming function  
1.4 Specification Comparison Chart  
9
 
 
Auto Zooming Tracking Dome Camera User Manual  
TRKPTZ-  
TRKPTZ-  
TRKPTZ-  
TRKP  
TZ-22  
00PT  
TRKPTZ-  
TRKPTZ-  
23X  
1801  
1802  
1803  
22X  
Model  
Signal Format  
Image Sensor  
PAL/NTSC  
¼ inch color CCD  
480 TVL  
Horizontal Resolution  
Video Out  
1.0±0.2VP-P  
P/T Speed  
Pan:0.05º240º/sec;Tilt:0.03º160º/sec  
S/N Ratio  
50DB  
0.01Lux  
0.01Lux  
Sensitivity  
IR cut Filter  
AGC  
1Lux  
0.1Lux  
1Lux 0.1Lux  
No  
No  
Yes  
Yes  
Auto/Manual  
Auto/Manual  
BLC  
F1.6-F3.7  
F1.4-F3.0 f=4.1-73.8mm  
/ F1.6-F3.8 f=3.5-91mm  
F1.6-F3.8  
f=4-88mm  
Lens  
f=3.6-82.8mm  
10  
 
Auto Zooming Tracking Dome Camera User Manual  
Optical Zoom  
Digital Zoom  
Panning  
18X  
12X  
22X  
23X  
8X  
Pan: 360ºContinuous;Tilt:-5º92º  
Range  
Preset  
256  
Number  
Auto Cruise  
Patterns  
Auto switch from 1 to 30 preset position sequentially  
4
8
4
2
Zone  
Alarm input  
Alarm output  
Windows  
8
blanking  
Interface  
Baud Rate  
Address  
RS-485  
1200bps , 2400bps, 4800bps, 9600bps , 19200bps  
0255  
24VAC  
Input voltage  
Input power  
Operating  
Temperature  
Dome Size  
20WWithout Heater/50WWith Heater)  
-2570Without Heater/-5070With  
Heater)  
6 inch  
11  
 
Auto Zooming Tracking Dome Camera User Manual  
Section 2 Normal Operation  
These operating instructions cover the basic operation of the  
dome and its features. When the dome is used with other  
manufacturerscontrol system, please refer to the system  
controllers instructions. In the event of special requirements  
outside the scope of this document it is prefer to contact your  
local distributor.  
Below instructions are based on using control keyboard as  
controlling device.  
(1) Dome Self-testing after Powered up  
After powered up, the dome will conduct reset procedure. In  
this procedure, the dome firstly pans to the default horizontal  
origin point, and finally tilts to the vertical 45° position to  
complete the self-testing. After the dome stops, it means the  
camera has completed the self-testing and is ready to receive  
control commands.  
(2) Pan and tilt: Move joystick up, down, right, left.  
(3) Set up preset  
Move to next position. Then press PRESET + NUM preset  
NO.+ ENTER and the dome will save current horizontal angle  
and title angle of pan / tilt / zoom and position parameters into  
memory.  
(4) Call preset  
Press PRESET + NUMPreset NO.+ ENTER , and the  
12  
 
 
Auto Zooming Tracking Dome Camera User Manual  
dome will calls these parameters saved in memoriy and adjust  
Pan/Tilt/Zoom of the camera to that position.  
Presets 1  
80  
Function  
Presets 2  
37  
Auto tracking  
Auto switch sequentially among preset  
positions  
82  
19  
83  
95  
97  
98  
99  
Clear all presets positions  
Select main programming menu  
Random scanning  
20  
28  
30  
31  
32  
Frame scanning  
Start auto scanning  
Extended Presets  
Note: For others dynamics controllers with only 64 or 40  
presets. On the menu of PRESETS NUMBER, set it as 64 or 40.  
Then you can use presets listed in Presets 2in stead.  
(5) Zoom: You can press IN or OUT key continuously or  
revolve the joystick to get desired zooming times.  
(6) Focus: press FAR or NEAR key.  
(7) Iris: Press OPEN or CLOSE key.  
Section 3 Menu Configuration  
You need to install the dome system before using this  
13  
 
 
Auto Zooming Tracking Dome Camera User Manual  
manual. Please refer to the installation packet supplied with the  
back box for installation instructions.  
After installed properly, power up the camera. It will start a  
configuration sequence. After the configuration is done, the  
monitor will display as below.  
PTOLPELCO-D  
COMM2400,N,8,1  
ADDR0  
This information will remain on the monitor until dome  
operation begins.  
Please refer to the following pages for more about how to  
operate and program the camera.  
Access main menu (preset 95): Please refer to the  
Accessing Main Menu (Preset 95) section.  
(1) Move joystick to position the cursor beside menu  
selection.  
(2) Move the joystick up or down to submenu/cursor  
selections.  
(3) Press iris Open to confirm selection.  
(4) Press iris Close to cancel selection.  
(5) Below instructions are based on using control keyboard  
as control device.  
14  
 
Auto Zooming Tracking Dome Camera User Manual  
3.1 Main Menu  
Set 95# preset to access main menu.  
MAIN MENU  
< SYSTEM INFORMATION >  
< DISPLAY SETUP >  
< DOME SETTINGS 1>  
< DOME SETTINGS 2>  
<DOME LABLE>  
RESET CAMERA  
REBOOT SYSTEM  
LANGUAGE  
EXIT  
ENGLISH  
Figure 3.1 MAIN MENU  
Access other OSD menus:  
(1) Move the joystick up or down to position the cursor  
beside others OSD menus.  
(2) Press iris Open to confirm selection.  
3.2 Select Language  
The language for the on-screen menus is selectable.  
Available languages include English and Chinese. The factory  
default language is English.  
Changing the display language:  
(1) In main menu move the joystick to position the cursor  
beside LANGUAGE.  
(2) Press iris Open. The cursor moves to the right, beside  
the currently selected language.  
15  
 
   
Auto Zooming Tracking Dome Camera User Manual  
(3) Move the joystick up or down to view selections. Press  
iris Open to confirm selection. All on-screen menus are changed  
into the selected language.  
3.3 System Information  
Move joystick to select <system information>, press Open to  
confirm the system information menu shown as Fig 3.2.  
SYSTEM INFORMATION  
COMM  
9600N81  
255  
ADDRESS  
PROTOCOL  
PRESETS NUMBER  
LANGUAGE  
TEMPERATURE  
BACK  
PELCO-P  
256  
ENGLISH  
36°C  
EXIT  
Figure 3.2 SYSTEM INFORMATION  
The system information screen shows dome language,  
protocol, and other configuration information.  
System information settings shown are not changeable in  
this interface. It is for reference only.  
Follow the following steps to display the system information  
screen:  
(1) Move the joystick to position the cursor beside SYSTEM  
INFORMATION.  
16  
 
 
Auto Zooming Tracking Dome Camera User Manual  
(2) Press iris Open.  
3.4 Display Setup  
3.4.1 Display Setup  
Move joystick to select <DISPLAY SETUP>, press Open to  
enter the display setup menu shown as Fig3.3.  
DISPLAY SETUP  
PRESET LABEL  
ZONE LABEL  
ZOOM  
ON  
ON  
ON  
AZIMUTH/ELEVATION ON  
CAMERA LABEL  
<LABEL POSITION>  
BACK  
ON  
EXIT  
Figure 3.3 DISPLAY SETUP  
Display setup enables you to program how labels are  
displayed on the monitor. The following labels are available:  
PRESET LABEL: Identifying preset.  
ZONE LABEL: Identifying zone.  
ZOOM: Identifying zooming times.  
AZIMUTH/ELEVATION: Amount of pan from 0°and the  
amount of tilt from 0°horizontal.  
CAMERA LABEL: Identifying dome.  
A preset label is displayed when a preset is called. A zone  
label is displayed when the system moves into a zone. The zoom  
17  
 
   
Auto Zooming Tracking Dome Camera User Manual  
ratio label is displayed when zoom is activated.  
Azimuth/elevation and direction labels are displayed when  
pan/tilt is activated. The dome label is displayed when the dome  
label is activated.  
The following settings are available foe each label:  
OFF: The label is not displayed when activated.  
ON: The label shows when activated.  
3.4.2 Label Position  
Labels can be placed anywhere on the monitor. This feature  
enables you to customize the place of labels on monitor screen.  
ZONE  
CAMERA PRESET  
SAVE  
RESET  
AZIMUTH  
ZOOM  
Figure 3.4 Label Position  
To set a label position:  
(1) Move joystick to position the cursor beside a label.  
(2) Press iris Open.  
(3) Move joystick to move the label up, down, left, or right.  
(4) Press iris Open.  
(5) Repeat steps 1 through 4 to position other labels.  
(6) Move the cursor to Save and press iris Open to save  
settings and return to display setup menu.  
18  
 
 
Auto Zooming Tracking Dome Camera User Manual  
3.5 Dome Settings 1  
3.5.1 Dome Settings 1  
Move joystick to select <DOME SETTING 1>, press Open to  
enter the dome setting1 menu shown as Fig3.5.  
DOME SETTINGS1  
<CAMERA>  
<MOTION>  
<POWER UP>  
<PRESETS>  
<PATTERNS>  
<ZONES>  
<CLEAR>  
PRESET NUMBER  
BACK  
256  
EXIT  
Figure 3.5 Dome settings 1  
3.5.2 Camera Settings  
Move joystick to select <CAMERA>, press Open to enter  
the camera menu shown as Fig3.6.  
19  
 
     
Auto Zooming Tracking Dome Camera User Manual  
CAMERA  
ZOME LIMIT  
X46  
BACKLIGHT COMP  
<PROGRAM AE MODE>  
<OTHERS>  
ON/OFF  
BACK  
EXIT  
Figure 3.6 CAMERA  
ZOOM LIMIT:  
Zoom limit enables you to define a limitation on zooming  
times.  
BACKLIGHT COMPENSATION (BLC):  
If a bright backlight presents, the subjects in the picture may  
appear dark or as a silhouette. Backlight compensation  
enhances objects in the center of the picture. The dome uses the  
center of the picture to adjust the iris. If there is a bright light  
source outside this area, it will change to white. The camera will  
adjust the iris so that the object in the sensitive area is properly  
exposed.  
There are two backlight compensation settings:  
ON: Backlight compensation is activated.  
OFF (default): Backlight compensation is not activated.  
3.5.2.1 Program AE Mode  
Move joystick to select < PROGRAM AE CORTROL >, press  
Open to enter the PROGRAM AE CORTROL menu shown as  
Fig3.7  
20  
 
Auto Zooming Tracking Dome Camera User Manual  
PROGRAM AE CORTROL  
AE MODE  
AUTO  
AUTO  
1/50  
LOW LIGHT MODE  
LOW LIGHT LIMIT  
IRIS LEVEL  
F2.0  
AGC LEVEL  
0dB  
BIRGHT LEVEL  
0dB/F2.0  
BACK  
EXIT  
Figure 3.7A PROGRAM AE CORTROL  
PROGRAM AE COORTROL  
PROGRAM AE MODE  
AUTO  
IR CUT FILTER INISERT/REMOVE  
BACK  
EXIT  
Figure 3.7 B PROGRAM AE CORTROL  
Note: Figure 1.7A shows program AE mode, it is only for  
models names TRKPTZ18XX and TRKPTZ26XX. Figure 1.7B  
shows program AE mode, it is only for models named  
TRKPTZ22XX and TRKPTZ23XXPNT.  
() Figure 3.7A PROGRAM AE MODE setting for models  
named TRKPTZ18XX and TRKPTZ26XX.  
AE MODE:  
Settings include: AUTO, MANUAL , SHUTTER, IRIS, and  
BRIGHT.  
LOW LIGHT MODE:  
Settings include: AUTO and MANUAL.  
21  
 
Auto Zooming Tracking Dome Camera User Manual  
LOW LIGHT LIMIT  
Low light limit is the maximum duration, it is in fractions of a  
second, that electronic shutter will remain open in low light  
conditions. The default setting is 1/50.  
Settings include:1/2, 1/3, 1/6, 1/12, 1/25, 1/50, 1/75, 1/100,  
1/120, 1/150, 1/215, 1/300, 1/425, 1/600, 1/1000, 1/1250, 1/1750,  
1/2500, 1/3500, 1/6500, 1/10000.  
IRIS LEVEL  
Iris level is the lens function that automatically opens and  
closes the iris in response to changing light conditions. The  
default setting is F2.0.  
Settings include: F2.0, F1.6 , F1.4, Close, F22, F19, F16,  
F14, F11, F 9.6, F8.0, F6.8, F5.6, F4.8, F4.0, F3.4, F2.8, F2.4.  
AGC LEVEL  
AGC(Automatic Gain Control) automatically adjusts the  
amount of video amplification to maintain a Full 1-volt  
peak-to-peak video signal output. The default setting is 0 dB.  
Settings include: 0dB, 2 dB, 4 dB, 6dB, 8 dB, 10 dB, 12 dB,  
14 dB, 16 dB, 18 dB, 20 dB, 22 dB, 24 dB, 26 dB, 28 dB.  
BRIGHT LEVEL  
The default setting is 0 dB /F2.0.  
Settings include: 0 dB /F2.0, 0 dB /F1.6, 0 dB /F1.4, 2 dB /  
F1.4, 4 dB / F1.4, 6 dB / F1.4, 8 dB / F1.4, 10 dB/ F1.4, 12 dB/  
F1.4, 14 dB/ F1.4, 16 dB/ F1.4, 18 dB/ F1.4, 20 dB/ F1.4, 22 dB/  
F1.4, 24 dB/ F1.4, 26 dB/ F1.4, 28 dB/ F1.4, Close, 0 dB /F22, 0  
dB /F19, 0 dB /F16, 0 dB /F14, 0 dB /F11, 0 dB /F9.0, 0 dB /F 8.0,  
0 dB /F6.8, 0 dB /F5.6, 0 dB /F4.8, 0 dB /F4.0, 0 dB /F3.4, 0 dB  
/F2.8, 0 dB /F2.4.  
NOTE: LOW LIGHT LIMIT, IRIS LEVEL, AGC LEVEL  
BRIGHT LEVEL can set only when AE MODE and LOW LIGHT  
MODE are set as Manual.  
() Figure 3.7B PROGRAM AE MODE settings are for  
MODEL TRKPTZ18XX and TRKPTZ26XX.  
AE MODE  
Settings include: AUTO, AU+IR1, AU+IR2, AU+DSS,  
22  
 
Auto Zooming Tracking Dome Camera User Manual  
AU+DSS+IR1, AU+DSS+IR2, AU+DSS+IR3, SHUTTER PR,  
IRIS PRIO, and AGC PRIORI.  
IR CUT FILTER  
Settings include: IN and OUT.  
LOW LIGHT LIMIT  
Settings include: 1/1.5, 1/3, 1/6, 1/12, 1/25, 1/50.  
SHUTTER  
Settings include: 1/30000, 1/10000, 1/4000, 1/2000, 1/1000,  
1/500, 1/250, 1/150, 1/100, 1/50, 1/25, 1/12, 1/6, 1/3, 1/1.5.  
IRIS LEVEL  
Iris level is the lens function that automatically opens and  
closes the iris in response to changing light conditions. The  
default setting is F1.6.  
Settings include: F1.6, F2.2, F3.2, F4.4, F6.4, F8.8, F12, F17,  
F24, F34.  
AGC LEVEL  
AGC(Automatic Gain Control) automatically adjusts the  
amount of video amplification to maintain a Full 1-volt  
peak-to-peak video signal output. The default setting is 0 dB.  
Settings include: 0dB, 6dB, 12dB, 18dB, 24dB, and 30dB  
3.5.2.2 Other Menu  
Move joystick to select < others >, press Open to enter the  
others menu shown as Fig3.8.  
23  
 
Auto Zooming Tracking Dome Camera User Manual  
OTHERS  
IR CUT FILTER  
IR CUT FILTER  
AUTO IRIS  
AUTO  
COLOUR  
ON  
SHARPNESS  
ON  
SHARPNESS LEVEL  
5
AUTO WHITE BALANCE ON/OFF  
R GAIN  
B GAIN  
214  
164  
BACK  
EXIT  
Figure 3.8A OTHER MENU  
OTHERS  
AUTO IRIS  
ON  
91  
AUTO IRIS LEVEL  
AUTO IRIS PEAK  
SHARPNESS  
SHARPNESS LEVEL  
AUTO WHITE BALANCE  
R GAIN  
16  
ON  
39  
ON  
652  
427  
B GAIN  
BACK  
EXIT  
Figure 3.8B OTHER MENU  
Note: Figure 3.8A shows Other Menu only for models named  
TRKPTZ18XX and TRKPTZ26XX. Figure 3.8B shows Other  
Menu only for the models named TRKPTZ22XX and  
TRKPTZ23XX.  
AUTO IRIS:  
Auto iris is the lens function that automatically opens and  
24  
 
Auto Zooming Tracking Dome Camera User Manual  
closes the iris in response to changing light conditions.  
Program the auto iris to operate automatically or at a  
user-defined level.  
OFF: Auto iris is disabled, and for manually control only.  
AUTO: The iris is adjusted automatically to produce a  
constant video output as determined by the Auto Iris level setting.  
NOTE: If auto iris is in auto mode, it will remain that status  
until the iris is manually opened or closed. The dome will return  
to auto mode when it pans or tilts more than 15 degrees.  
AUTO SHARPNESS:  
Auto sharpness enhances picture details by increasing the  
aperture gain of the camera and sharpening the edges in the  
picture.  
There are two settings:  
ON (default): The camera automatically keeps at a normal  
sharpness mode.  
OFF: The sharpness of the picture is set manually by  
programming the sharpness level.  
AUTO WHITE BALANCE:  
This feature automatically processes the viewed image to  
retain color balance over a color temperature range. The default  
setting for auto white balance is ON.  
R GAN: Adjusts the picture output in the red range. As you  
change the value, the color changes on your monitor.  
B GAN: Adjusts the picture output in the blue range. As you  
25  
 
Auto Zooming Tracking Dome Camera User Manual  
change the value, the color changes on your monitor.  
3.5.3 Motion Setting  
Move joystick to select <MOTION >, press Open to enter the  
motion menu shown as Fig3.9.  
MOTION  
AUTO FLIP  
ON/OFF  
PROPORTIONAL PAN  
ON/OFF  
PARK TIMEMINUTES)  
PARK ACTION  
SCAN SPEEDDEG/S)  
< SET SCAN>  
0
NONE  
1
< MANUAL LIMIT>  
< SET AZIMUTH ZERO>  
< CLEAR AZIMUTH ZERO>  
BACK  
EXIT  
FIGURE 3.9 MOTION MENU  
AUTO FILP:  
When the dome camera tilts downward and goes just  
beyond the vertical, the dome camera rotates 180 degrees  
automatically. Afterwards, the dome camera starts moving  
upward even you still hold joystick in the down position. Once  
you let go of the joystick after the dome rotates, joystick control  
returns to normal operation. The auto-flip feature is useful for  
following a person who passes directly beneath the dome.  
There are two auto flip modes:  
ON (default): Auto flip mode enabled.  
OFF: Auto flip mode disabled.  
26  
 
 
Auto Zooming Tracking Dome Camera User Manual  
PROPORTIONAL PAN:  
Proportional pan automatically reduces or increases the pan  
and tilt speeds in proportion to the zooming times. At telephoto  
zoom settings, the pan and tilt speeds will be slower for a given  
amount of joystick deflection then at wide zoom settings. This  
keeps the image from moving too fast on the monitor when there  
is a large amount of zoom.  
There are two proportional pan modes:  
ON (default): Enables the proportional pan mode.  
OFF: Disables proportional pan mode. The pan speed will  
not depend on the zooming times.  
PARK TIME:  
This feature enables the dome to operate a specified activity  
(scan, preset, or pattern) after a programmed time of idleness.  
Park time can be programmed from 1 minute to 720  
minutes (12 hours), or set to zero, which disables this feature.  
The default setting is zero.  
PARK ACTION:  
This feature will define the activity when the dome parks.  
The following settings are available:  
NONE (default): No action.  
AUTO SCAN: Dome starts auto scan operation.  
RANDOM SCAN: Dome starts frame scan operation.  
FRAME SCAN: Dome starts frame scan operation.  
PRESET 1: Dome goes to preset 1.  
PRESET 8: Dome goes to preset 8.  
PANTTERN 1: Dome runs pattern1.  
PANTTERN 2: Dome runs pattern2.  
27  
 
Auto Zooming Tracking Dome Camera User Manual  
PANTTERN 3: Dome runs pattern3.  
PANTTERN4: Dome runs pattern4.  
SCAN SPEED:  
Scan speed is that the dome will pan when in a FRAME  
SCAN mode. Scan speed is adjustable from 1 to 32 via the  
programming menu.  
SET SCAN STOPS:  
Set Scan Stops are programmable stops that limit the pan  
range of the dome. There must be two limits, a left and a right, to  
define an area. The dome reverses direction frame scanning  
when a limit stop is reached.  
To set scan stops:  
(1) Move joystick to position the cursor beside set scan  
stops.  
(2) Press iris Open.  
(3) Follow the directions displayed on the monitor.  
CLEAR SCAN STOPS:  
To clear scan stops:  
(1) Move joystick to position the cursor beside clear scan  
stops.  
(2) Press iris Open.  
(3) Follow the directions displayed on the monitor.  
SET MANUAL LIMIT:  
<Set manual limit > is to set the P/T/Zs moving range.  
To set manual limit:  
(1) Move joystick to position the cursor beside set manual  
limit.  
(2) Press iris Open.  
28  
 
Auto Zooming Tracking Dome Camera User Manual  
(3) Follow the directions displayed on the monitor.  
SET AZIMUTH ZERO:  
Azimuth is the pan angle from 0°to 359°.Azimuth zero is  
the pan position you specify to be the 0°point. Azimuth zero is  
normally set to magnetic north. Once set, azimuth and compass  
readings are based on the set Azimuth Zero point.  
To program azimuth zero:  
(1) Move joystick to position the cursor beside set azimuth  
zero.  
(2) Press iris Open.  
(3) Follow the directions displayed on the monitor.  
CLEAR AZIMUTH ZERO:  
(1) Move joystick to position the cursor beside CLEAR  
AZIMUTH ZERO.  
(2) Press iris Open  
(3) Follow the directions displayed on the monitor.  
3.5.4 Power Up  
Move joystick to select <power up>, press Open to enter the  
power up menu shown as Fig3.10.  
POWER UP  
POWER UP ACTION NONE  
BACK  
EXIT  
Figure 3.10 POWER UP  
POWER UP ACTION:  
29  
 
 
Auto Zooming Tracking Dome Camera User Manual  
This setting defines a specific activity (scan, preset, pattern)  
to be performed after the dome is powered up.  
Following settings are available:  
NONE (default): No action.  
AUTO SCAN: Dome starts auto scan operation.  
RANDOM SCAN: Dome starts random scan operation.  
FRAME SCAN: Dome starts frame scan operation.  
PRESET 1: Dome goes to preset 1.  
PRESET 8: Dome goes to preset 8.  
PATTERN 1:Dome runs pattern 1.  
PATTERN 2:Dome runs pattern 2.  
PATTERN 3:Dome runs pattern 3.  
PATTERN 4:Dome runs pattern 4.  
3.5.5 Presets Setting  
Move joystick to select <PRESETS>, press Open to enter  
the presets menu shown as Fig3.11.  
PRESETS  
PRESET NUMBER  
1
PRESET NOT DEFINEO…  
< EDIT PRESET LABEL >  
< EDIT PRESET SCAENE >  
< CLEAR PRESET >  
BACK  
EXIT  
Figure 3.11 PRESET  
The dome camera has 64 programmable preset positions.  
Follow below steps to program a preset.  
30  
 
 
Auto Zooming Tracking Dome Camera User Manual  
(1) Select preset number:  
a. Move joystick to position the cursor beside PRESET  
NUMMBER, press iris Open.  
b. Move the joystick up or down to view selections. Press  
iris Open to confirm selection.  
(2) Edit preset label.  
a. Move joystick to position the cursor beside EDIT Preset  
label.  
b. Press iris Open. It will show:  
PRESET NUMBER  
1
PRESET LABLE  
0 1 2 3 4 5 6 7 8 9 Y Z y z  
1 - - - - -  
A B C D E F G H I J K L M N O P Q R S T U V W X  
a b c d e f g h I j k l m n o p q r s t u v w x  
INPUT MODE  
OK CN  
CHARACTER  
BP  
SP  
Figure 3.12 CHARACTER INPUT  
c. Move joystick to position the cursor beside a character.  
Press iris Open to confirm selection. To clear a character,  
position the cursor beside BPE, and then press iris Open.  
d. After the label is inputted, move the cursor to Ok, then  
press iris Open to save and return to the Preset menu.  
e. After the label is inputted, move the cursor to CE, then  
press iris Open to cancel and return to the Preset menu.  
31  
 
Auto Zooming Tracking Dome Camera User Manual  
(3) Edit preset scene:  
a. Move joystick to position the cursor beside EDIT  
PRESET SCENE.  
b. Press iris Open.  
c. Follow the direction displayed on the monitor.  
(4) Clear a preset:  
a. Move joystick to position the cursor beside CLEAR  
PRESET.  
b. Press iris Open.  
c. Follow the direction displayed on the monitor.  
3.5.6 Patterns Setting  
Use stick to select <patterns> Open to enter the patterns  
menu shown as Fig3.13.  
PATTERNS  
PATTERN NUMBER  
<PROZGRSM PATTERN>  
<CLEARE PATTERN>  
BACK  
1
EDIT  
Figure 3.13 PATTERNS  
PROGRAME PATTERN:  
A pattern is function that the camera can save its moving  
course, and will repeat that course when demanded.  
To program a pattern:  
(1) Move joystick to position the cursor beside PATTERN  
NUMBER, and then press iris Open.  
32  
 
 
Auto Zooming Tracking Dome Camera User Manual  
(2) Move the joystick up or down to view selections. Press  
iris Open to confirm selection.  
(3) Move joystick to position the cursor beside PROGRAM  
PATTERN.  
(4) Press iris Open.  
(5) Follow the directions displayed on the monitor.  
After a pattern is programmed, the remaining storage  
percentage will be displayed on the screen. This is the amount of  
memory available to program the remaining patterns.  
CLEAR PATTERN:  
(1) Move joystick to position the cursor beside CLEAR  
PATTERN.  
(2). Press iris Open.  
(3) F0llow the directions displayed on the monitor.  
3.5.7 Zone Setting  
Move joystick to select <ZONES>, then press Open to enter  
the zones menu shown as Fig 3.14.  
ZONES  
ZONE NUMBER  
1
ZONE NOT DEFINEO…  
<EDIT ZONE LABEL>  
<EDIT ZONE>  
ZONE  
ENABLED  
ON  
<CLEAR ZONE >  
BACK  
EXIT  
Figure 3.14 ZONES SETTING  
33  
 
 
Auto Zooming Tracking Dome Camera User Manual  
A zone is pan area, defined by a left and right limit on the  
360-degree pan plane. There are altogether eight zones, each  
can be with a 6-character label.  
TO program a zone:  
(1) Move joystick to position the cursor beside ZONE  
NUMBER. Press iris Open.  
(2) Move the joystick up or down to view selections. Press  
iris Open to confirm selection.  
(3) Move joystick to position the cursor beside EDIT ZONE.  
(4) Press iris Open. The Zone programming window will  
show on the monitor.  
(5) Follow the directions displayed on the monitor. After the  
left stops and right limit stops are set, the Zones menu reappears  
with the ZONE ENABLED option set to be ON.  
To edit a zone label:  
(1) Move joystick to position the cursor beside EDIT ZONE  
LABEL.  
(2) Press iris Open. It will show as follows:  
ZONE NUMBER  
1 - - - - -  
1
ZONE LABLE  
0 1 2 3 4 5 6 7 8 9 Y Z y z  
A B C D E F G H I J K L M N O P Q R S T U V W X  
a b c d e f g h I j k l m n o p q r s t u v w x  
INPUT MODE  
OK CN  
CHARACTER  
BP  
SP  
Figure 3.15 ZONE SETTING  
34  
 
Auto Zooming Tracking Dome Camera User Manual  
(3) Move joystick to position the cursor beside a character.  
Press iris Open to confirm selection. To clear a character,  
position the cursor beside BP, and then press iris Open.  
(4) When a label is inputted, move the cursor to Ok, then  
press iris Open to save and return to the Preset menu.  
(5) When a label is inputted, move the cursor to CN, then  
press iris Open to cancel and return to the Preset menu.  
To clear a zone:  
(1) Move joystick to position the cursor beside CLEAR  
ZONE.  
(2) Press iris Open. Follow the instructions on the screen.  
Note: The ZONE NUMBER 9 is the domes label.  
3.5.8 Clears Setting  
Move joystick to select <CLEARS>, then press Open to  
enter the clears menu shown as Fig 3.16.  
CLEARS  
CLEAR ZONES  
CLEAR PARESETS  
CLEAR PATTERNS  
RESTORE FACTORY DEFAULTS  
BACK  
EXIT  
Figure 3.16 CLEARS SET  
CLEAR ZONES:  
Clear all zones. To clear a specific zone, please refer to  
35  
 
 
Auto Zooming Tracking Dome Camera User Manual  
ZONES section.  
CLEAR PRESETS:  
Clear all presets. To clear a specific preset, please refer to  
the PRESETS section.  
CLEAR PATTERNS:  
Clear all patterns. To clear a specific pattern, please refer to  
the PATTERNS section.  
RESTORE FACTORY DEFAULTS:  
This is to restore leaving-factorys default settings.  
3.5.9 Presets Number  
This is to set the domes preset number.  
3.6 Dome Settings 2 Menu  
Move joystick to select <DOME SETTINGS 2>, then press  
Open to enter the dome settings 2 menu shown as Fig 3.17.  
DOME SETTINGS 2  
<ALARMS>  
<AUX>  
<PASSWORD>  
<WINDOWS BLANKING>  
<HEATER SETTING>  
CRUISE SETTING  
TRACKING SETTING  
BACK  
EXIT  
36  
 
   
Auto Zooming Tracking Dome Camera User Manual  
Figure 3.17 DOME SETTINGS  
3.6.1 Alarms  
Move joystick to select <ALARMS>, then press Open to  
enter the alarms menu shown as Fig 3.18.  
ALARMS  
ALARM NUMBER  
SEQUENCE(SECS)  
< ALARM SETTINGS >  
<CLEAR SET>  
BACK  
1
1
EXIT  
Figure 3.18 ALARMS  
The dome has seven alarm inputs, which can be  
programmed as high, medium or low priority. When an alarm is  
received, the inputted signal to the dome triggers the  
userdefined action (go to preset, run pattern, etc.) programmed  
for the alarm.  
There are three alarm settings:  
ALARM NUMBER:  
Use this to select alarms number.  
SEQUENCE<SECS>:  
This is the time the dome will perform an alarm activity when  
more than one alarm of the same priority occurs at the same  
time.  
RESET DELAY<SECS>:  
37  
 
 
Auto Zooming Tracking Dome Camera User Manual  
This is the length of time the dome considers the alarm to be  
active after it has physically cleared.  
3.6.2 Alarms Setting  
Move joystick to select <ALARM NUMBER>, then press  
Open to enter the alarm number menu shown as Fig 3.19.  
ALARM NUMBER  
ALARM PRIORITY  
ALARM ACTION  
ACTIVATE AUX  
ALARM CONTACT  
BACK  
1
LOW  
NONE  
OPEN  
OPEN  
EXIT  
Figure 3.19 ALARM SETTINGS  
Follow below steps to program alarm settings.  
Select alarm number:  
(1) a. Move joystick to position the cursor the cursor beside  
ALARM NUMBER.  
b. Press iris Open.  
c. Move the joystick up or down to view selections. Press iris  
Open to confirm selection.  
(2) Move the joystick to position the cursor beside Alarm  
Settings. Press iris Open.  
Select alarm priority:  
(1) Move joystick to position the cursor beside Alarm Priority.  
38  
 
 
Auto Zooming Tracking Dome Camera User Manual  
(2) Press iris Open.  
(3) Move the joystick up or down to view the available  
selections. Available settings include HIGH, MEDIUM, and LOW  
(default). If multiple alarms with different priorities are active at  
the same time, the dome will only go to the alarms with the  
highest priority.  
(4) Press iris Open to confirm selection.  
Set alarm action:  
(1) Move joystick to position the cursor beside Alarm action.  
(2) Press iris Open.  
(3) Move the joystick up or down to view the available  
selections. Below are the settings for alarm action:  
NONE: No action when alarm is triggered.  
PRESET: Dome goes to the preset that is the same as the  
alarm number. E.g. preset 1 will go to Alarm 1.  
PATTERN 1: Dome runs pattern 1 when alarm is triggered.  
PATTERN 2: Dome runs pattern 2 when alarm is triggered.  
PATTERN 3: Dome runs pattern 3 when alarm is triggered.  
PATTERN 4: Dome runs pattern 4 when alarm is triggered.  
AUTO SCAN: Dome starts auto scan operation when alarm  
is triggered.  
RANDOM SCAN: Dome starts RANDOM scan operation  
when alarm is triggered.  
FRAME SCAN: Dome starts FRAME scan operation when  
alarm is triggered.  
TRACKING: Dome calls preset and start auto tracking.  
Tracking function only available with the models named  
TRKPTZ18XXPT, TRKPTZ22XXPT, TRKPTZ23XXPNT and  
TRKPTZ26XXPNT.  
(4) Press iris Open to confirm selection.  
39  
 
Auto Zooming Tracking Dome Camera User Manual  
Set auxiliary to activate:  
(1) Move joystick to position the cursor beside ACTIVATE  
AUX.  
(2) Press iris Open.  
(3) Move the joystick up or down to view the following  
available selections.  
OFF (default): Not activated.  
1:An alarm action will close AUX 1.  
2: AN alarm action will close AUX 2.  
(4) Press iris Open to confirm selection.  
Set alarm contact:  
(1) Move joystick to position the cursor beside ALARM  
CONTACT.  
(2) Press iris Open.  
(3) Move the joystick up or down to view the following  
available selections.  
OFF (default): close  
ON: open.  
(4) Press iris Open to confirm selection.  
3.6.3 Aux Setting  
Move joystick to select <AUX>, then press Open to enter the  
aux menu shown as Fig 3.20.  
40  
 
 
Auto Zooming Tracking Dome Camera User Manual  
AUX  
DWELL TIME<SECS> 1  
DWELL TIME<SECS> 2  
BACK  
0
0
EXIT  
Figure 3.20 AUX  
An auxiliary output is a programmable signal from the dome  
back box that can trigger another device to operate. An auxiliary  
out put is programmable to trigger from an alarm or from a  
controller.  
An AUX 1 command from the controller will place a ground  
at the output of AUX 2 to operate the device that is connected to  
it.  
Setting include: 0~30secs.  
An AUX 2 command from the controller will place a ground  
at the output of AUX 2 to operate the device that is connected to  
it.  
Setting include: 0~30secs.  
3.6.4 Password Setting  
Move joystick to select <PASSWORD>, then press Open to  
enter the password menu shown as Fig 3.21.  
41  
 
 
Auto Zooming Tracking Dome Camera User Manual  
PASSWORED  
EBABLE PASSWORD  
<EDIT PASSWORD>  
BACK  
OFF  
EXIT  
Figure 3.21 PASSWORED  
This setting protects it from unauthorized changes to the  
dome settings.  
ENABLE PASSWORD:  
Open or close the password features.  
EDIT PASSWORD (Four Numbers):  
PLEASE INPUT OLD PASSWORED  
PASSWORD  
1 2 3 4 5 6 7 8 9 0  
CLEAR  
ENTER  
EXIT  
Figure 3.22 EDIT PASSWORD  
(1) Move joystick to position the cursor beside a number.  
Press iris Open to confirm selection.  
(2) When password is inputted, move the cursor to ENTER  
and press iris Open comes to the PLEASE INPUT NEW  
PASSWORED.  
(3) Input four new passwords, move the cursor to ENTER  
then press iris Open and comes to PLEASE INPUT NEW  
PASSWORED. Input four new passwords.  
42  
 
Auto Zooming Tracking Dome Camera User Manual  
3.6.5 Windows Blanking  
Move joystick to select <WINDOWS BLANKING>, then  
press Open to enter the windows blanking menu shown as Fig  
3.23.  
WINDOWS BLANKING  
STYLE  
GRAY  
OFF  
OFF  
BLANK ALL ABOVE  
BALANK ALL BELOW  
<SET WINDOWS>  
BACK  
EXIT  
Figure 3.22 WINDOWS BLANKING  
Window blanking enables you to program up to eight,  
four-sided, user-defined areas that cannot be viewed by the  
operator of the dome system. A blanked area will move with pan  
and tilt functions and automatically adjust in size according to  
zoom times.  
Style:  
The dome has two styles for window blanking, GRAY and  
SMEAR. If style is set to gray, the blanked area is covered with a  
solid gray window. If smear is selected images behind the  
window will be noticeable but not distinguishable.  
BLANK ALL ABOVE/BLANK ALL BELOW:  
The dome camera has two style modes for window blanking,  
GRAY and SMEAR. If style is set to gray, the blanked area is  
covered with a solid gray window. If smear is selected images  
behind the window will be noticeable but not distinguishable.  
43  
 
 
Auto Zooming Tracking Dome Camera User Manual  
Blanking Parameters:  
BLANK ALL ABOVE  
BLANK ALL BELOW  
OFF  
0
No Blanking  
OFF  
0
No Blanking  
-5º~10º  
-5º~25º  
-5º~35º  
-5º~45º  
-5º~55º  
-5º~65º  
-5º~75º  
-5º~85º  
5º~92º  
-5º~92º  
5º~92º  
10  
20  
30  
40  
50  
60  
70  
10  
20  
30  
40  
50  
60  
70  
15º~92º  
25º~92º  
35º~92º  
45º~92º  
55º~92º  
80  
-5º~95º  
80  
70º~92º  
3.6.6 Set Windows  
Move joystick to select <SET WINDOWS>, then press Open  
to enter the set windows menu shown as Fig 3.24.  
SET WINDOWS  
WINDOWS NUMBER  
<EDIT WINDOWS LOCATION>  
<EDIT WINDOW ZOOM >  
ENABLE WINDOWS  
CLEAR WINDOWS  
BACK  
1
OFF  
EXIT  
Figure 3.24 SET WINDOWS MENU  
Windows Number: 1 ~ 8.  
<Edit windows location>: Edit the location of windows  
44  
 
 
Auto Zooming Tracking Dome Camera User Manual  
blanking  
<Edit window zoom>: set the zoom of the blanking. The  
blanking will take effect when the video is zoomed to this time or  
above.  
Enable Windows: Enable or disable the current blanking  
Clear windows: clear the current windows blanking  
Operation:  
1. Move joystick to select a item  
2. Press iris Open  
3. Move joystick to select parameters  
4. Press Open  
3.6.7 Edit Windows Location  
Move joystick and move cursor to < EDIT WINDOWS  
LOCATION >, then press open to enter the menu as Fig 3.25.  
EDIT WINDOWS LOCATION  
IRIS OPEN TO CONTINUE  
IRIS CLOSE TO CANCEL  
Figure 3.25 EDIT WINDOWS MENU  
Operation:  
1. From Fig 3.25, move cursor to make sure it is at the  
center points of blanking and coordinate.  
45  
 
 
Auto Zooming Tracking Dome Camera User Manual  
2. From the menu of Fig. 3.25, press Close to return to the  
menu of Fig 3.24  
3. From the menu of Fig. 3.25, press Open to enter menu of  
Fig 3.26 to edit the windows location.  
EDIT WINDOW LOCATION  
Figure 3.26 EDIT WINDOW LOCATION  
4. From the EDIT WINDOW LOCATION menu shown in Fig  
3.26:  
Move joystick left; zoom in (left/right) from the zone center.  
Move stick right; zoom in (left/right) from the zone center.  
Move stick up; zoom in (up/down) from the zone center.  
Move stick down; zoom in (up/down) from the zone center.  
5. After the zone is set, press Open to save the settings and  
return to menu of Figure3.24.  
3.6.8 Edit Windows Zoom  
From the menu of Figure 3.24, move stick and move cursor  
to <Edit Window Zoom>, press Open to enter below menu:  
EDIT WINDOWS  
IRIS OPEN TO CONTINUE  
IRIS CLOSE TO CANCEL  
Figure 3.27 EDIT WINDOWS  
Pan the joystick to adjust the zoom times.  
46  
 
 
Auto Zooming Tracking Dome Camera User Manual  
Press Close to discard the setting and return to Fig 3.24  
Press Open to save the setting and return to Fig 3.24.  
3.6.9 Heater Setting  
From the dome setting 2 menu shown in Fig3.17, move  
joystick and move cursor to HEATER SETTING, press Open to  
enter the following menu (Figure 3.28).  
HEATER SETTING  
HEATER DISPLAY  
HEATER MODE  
ON  
AUTO  
TEMPERATUEE SET 33℃  
BACK  
EXIT  
Figure 3.28 HEATER SETTING  
HEATER DISPLAY:  
Heater display shows heater state.  
ON: Screen will display heater state.  
OFF: Screen will not display heater state.  
HEATER MODE:  
Heater mode is to set the heaters startup mode.  
AUTO: Heater starts when temperature is lower than lower  
temperature.  
OFF: Heater is closed.  
ON: Heater is open.  
TEMPERATURE SET:  
47  
 
 
Auto Zooming Tracking Dome Camera User Manual  
Temperature set is to set the heaters startup temperature.  
Operations:  
1. Move joystick to select an item.  
2. Press Open.  
3. Move the stick to select a parameter.  
4. Press Open.  
3.6.10 Cruise Setting  
From the menu shown in Fig3.17, move joystick to select  
<CRUISE SETTING>, press Open to enter the following menu.  
CRUISE  
DWELL TIME<SECS>  
PRESET LIST  
1 ON  
7
1
0 OFF  
1 2 3 4 5 6 7 8 9 0  
0 1 1 0 0 1 0 1 1 1  
BACK  
EXIT  
Fig 3.29 CRUISE  
Dwell Time: the lasting time of preset, from 5~250 seconds  
Preset List: parameter 1, 2, 3  
Operations:  
1. In the menu, move the joystick to select a specific item.  
2. Press Open.  
3. Select the parameter with the joystick.  
4. Press Open  
48  
 
 
Auto Zooming Tracking Dome Camera User Manual  
1 ON 0 OFF: Note, they are not changeable,  
1234567890: display info, not changeable. When the preset  
list is 1, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0indicates presets from 1 ~ 10.  
When it is 2, it indicates presets from 11 ~ 20. When it is 3, it  
indicates presets from 21 ~ 30.  
0 0 0 0 0 1 0 1 0 1: select the cruising presets. 1 for cruising,  
0 for not cruising.  
Operations:  
1.From the menu in Fig3.21, select relative item of  
1234567890with the joystick.  
2. Press Open and select a specific parameter.  
Select options with joystick.  
3.6.11 Tracking Setting  
Move joystick to select <TRACKING SETTING>, press  
Open to enter the tracking menu shown as Fig 3.30.  
TRACKING SETTING  
DEFAULT SETTING  
SIZE SNS  
MIDIUM  
GRAY SNS  
MIDIUM  
LOST ACT  
TO HOME & TRACKING  
AUTO ZOOMING  
WAIT TINE<S>  
ON  
40  
<TRACKING BOUNDARY>  
BACK  
EXIT  
Figure 3.30 TRACKING SETTING  
Default Setting: tracking setting to default.  
49  
 
 
Auto Zooming Tracking Dome Camera User Manual  
Size SNS: the size of the target in the screen, Medium,  
Large, Small are selectable  
GRAY SNS: the sensitivity of the moving object, Medium,  
High and Low are selectable  
LOST AC: the action when the moving object is lost.  
Parameters include: return home and tracking, keep tracking,  
stop tracking  
AUTO ZOOMING: The dome will auto zoom in / out  
according to the size and distance of the object. Parameters can  
be ON/OFF.  
WAIT TIME <S>: When the tracking object is lost, the  
interval of time for the dome to wait before Lost Action.  
Parameters can be 5, 10, 15, 20, 25, 30, 35, 40 seconds.  
<TRACKING BOUNDARY>: to set the valid area of tracking  
function (UP/DOWN/LEFT/RIGHT).  
Operations:  
1. In the menu of Fig 3.30, move joystick to a specific item  
2. Press Open  
3. Move joystick to select desired parameter  
4. Press Open  
50  
 
Auto Zooming Tracking Dome Camera User Manual  
3.6.12 Tracking Boundary  
From the menu in Fig3.30, move the cursor to < TRACKING  
BOUNDRAY >, press Open to enter the following menu (Figure  
3.31)  
TRACKING BOUNDARY  
BOUNDARY LIMIT  
CLEAR BOUNDARY  
LEFT LIMIT  
RIGHT LIMIT  
UP LIMIT  
OFF  
OFF  
OFF  
OFF  
OFF  
DOWN LIMIT  
BACK  
EXIT  
Figure 3.31 TRACKING BOUNDARY  
BOUNDAR LIMIT: enable / disable the boundary  
CLEAR BOUNDARY: clear setting of the current boundary  
LEFT LIMT: set the left tracking boundary  
RIGHT LIMT: set the right tracking boundary  
UP LIMT: set the up tracking boundary  
DOWN LIMT: set the down tracking boundary  
Operations:  
1. Move the cursor to a specific function item  
2. Press Open  
3. Move the joystick to select parameter or operate as per  
screen instructions  
3. Press Open  
51  
 
 
Auto Zooming Tracking Dome Camera User Manual  
3.7 Dome Label  
From the menu shown in Fig3.1, move the cursor to  
<DOME LABEL>, press Open to enter the following menu  
(Figure .32)  
DOME LABLE  
<EDIT DOME LABEL>  
<CLEAR DOME LABEL>  
BACK  
EXIT  
Figure 3.32 DOME LABLE  
<EDIT DOME LABEL>: To edit the dome description and  
information. Please refer to 3.5.4 Edit Preset Label.  
<CLEAR DOME LABLE>: Clear current dome label. Press  
Open to enter the menu and then operate with instructions.  
3.8 Other Functions  
RESET CAMERA:  
If the camera does not operate or if you close cameras  
control, cycle camera power. Cycling camera power resets the  
camera but does not change any saved camera settings.  
REBOOT SYSTEM:  
Reboot the system if it does not operate or if there is no  
control. Rebooting the system will cycle dome and camera power  
without changing programmed dome settings. Ω  
52  
 
   

NAD CD Player C542 User Manual
NEC Laptop M380 User Manual
Newcon Optik Binoculars NV66 G2 4x User Manual
Nikon Camcorder S7000 User Manual
Nokia Stereo System DIGITAL MULTIMEDIA TERMINAL User Manual
Nortel Networks Switch 5510 User Manual
Omnimount Projector Accessories 3N1 PJT User Manual
OPTI UPS Surge Protector SBAH 821 User Manual
Panasonic DVR DMR EH65 User Manual
Panasonic Switch CR Relays User Manual